Remote Control Reference
1. Preparation
Section titled “1. Preparation”The network control interface must be enabled. You can find the network related options in the application menu: “Options → Settings → Remote Control”.

You must enable the desired interface type first. Then you should configure the network adapter and port to use. The special adapter ip 0.0.0.0 represents all available network adapter of used pc. After an restart of the application, the configured interface is available.
2. Usage
Section titled “2. Usage”There are two ways to send commands.
- You can use each browser application to send a command request. Please type the command string with leading ip and port address in the address bar and press the enter button. e.g. “http://192.168.2.20:8080/player.htm?state=play“. The server will answer with a HTTP response header and attached HTTP side or attached response string.
- You can use your own network tool, media control solution or with the installation distributed test tools, to send command to the server. There a two ways to send the command string:
- You can send a simple command string, terminated with “
\r” or “” character(s) (0xD 0xAhexadecimal,<CR><LF>or0xAhexadecimal,<LF>). E.g.“player.htm?state=play\r\n“If you use the TCP interface, the server will answer with a simple response string. If you use the UDP interface, the server will send no answer (fire and forget). - If you use the TCP interface, you can send a command request encapsulated in a minimum HTTP header, using the GET method. E.g. “
GET /player.htm?state=play HTTP/1.1\r\n\r“ The server will answer with a HTTP response header and attached HTTP side or attached response string.
- You can send a simple command string, terminated with “
3. Test Tools
Section titled “3. Test Tools”If you have chosen install „Shared Components“ during Installation, there are several tools to equip you to test:
- TCP-/ UDP-interface
- command behavior
- spy/ record network communication with third party software
You can execute/ find the test tools over the application startmenu entry; sub-entry “Tools”. Except TCP Test Tool 2, each of the described test tools below, have a command line interface. With the command line interface you are able to use the test tools in scripts, links and so on. You can find a documentation of available command line options inside sub-entry “Manuals”.
3.1. TCP Test Tool 2
Section titled “3.1. TCP Test Tool 2”With the TCP Test Tool 2 you can test the TCP interface using a permanent (long live) connection to one target. This tool also display a log of all network operations.

You can specify one target by adding the IP of the remote pc to the target list. By pressing the “Send” button, the tool:
- creates a connection to the current treated target
- sends the command string as simple string (see above)
- waits for response
- depicts the response string inside the response area on right side of the application
- and closes the connection to the current treated target.
3.1.1. Where to find it
Section titled “3.1.1. Where to find it”Software location after installation of VIOSO, Anyblend, Anyblend VR&SIM or VIOSO Player:
- Via Windows Start Menu:
All Programs / VIOSO 6 / Tools / TCP Test Tool - Exe file location:
C:\Program Files\VIOSO[version]\Shared Tools\ VIOSO_TCP_Test.exe
3.1.2. Command line usage
Section titled “3.1.2. Command line usage”Available parameters:
| Parameter | Description |
|---|---|
/D:"ip" |
ip of the destination if /D is not specified, the app will be configured for broadcasting |
/P:# |
# => port number |
/C:"..." |
“...” => command string to send (plain) |
/A |
if set, the application tries to send the command and closes app automatically |
Example:
VIOSO_TCP_Test2.exe/D:"192.168.2.2" /P:801 /C:"control.htm?present=1" /ASends the command “control.htm?present=1” to 192.168.2.2, using port 801 automatically.
Exit code:
VIOSO_TCP_Test2.exe returns an exit code on exit:
0: successful1: an error occurred (Command could not be sent to all destinations.)
3.2. TCP Test Tool
Section titled “3.2. TCP Test Tool”The TCP Test Tool is the predecessor to TCP Test Tool 2.

This tool does the same actions as it successor TCP Test Tool 2, but does not use a permanent connection and does not monitor all network traffic. It just outputs the response of the target.
We recommend to use TCP Test Tool 2 whenever possible.
3.2.1. Where to find it
Section titled “3.2.1. Where to find it”Software location after installation of VIOSO Anyblend, Anyblend VR&SIM or VIOSO Player:
- Via Windows Start Menu:
All Programs / VIOSO [version] / Tools / TCP Test Tool 2 - Exe file location:
C:\Program Files\VIOSO6\Shared Tools\ VIOSO_TCP_Test2.exe
See previous chapter for command line parameters.
3.3. UDP Test Tool
Section titled “3.3. UDP Test Tool”With the UDP Test Tool you are able to test the UDP interface.

You can specify one ore more targets by adding the IP of a desired PC to the target list. Beside this option, the tool is able to send the command string as broadcast to all computers in network.
By pressing the “Send” button, the tool sends a datagram, containing the command string, to all selected targets successively. If you use the broadcast option, the tool sends a broadcast datagram.
3.3.1. Where to find it
Section titled “3.3.1. Where to find it”- Via Windows Start Menu:
All Programs / VIOSO [version] / Tools / UDP Test Tool - Exe file location:
C:\Program Files\VIOSO6\Shared Tools\ VIOSO_UDP_Test.exe
3.3.2. Command line usage
Section titled “3.3.2. Command line usage”Available parameters:
| Parameter | Description |
|---|---|
/D:"ip" |
ip of the destination if /D is not specified, the app will be configured for broadcasting |
/P:# |
# => port number |
/C:"..." |
“...” => command string to send (plain) |
/A |
if set, the application tries to send the command and closes app automatically |
Example:
VIOSO_UDP_Test.exe /D:"192.168.2.2" /P:801 /C:"control.htm?present=1" /ASends the command “control.htm?present=1” to 192.168.2.2, using port 801 automatically.
Exit code:
VIOSO_TCP_Test2.exe returns an exit code on exit:
0: successful1: an error occurred (Command could not be sent to all destinations.)
4. Command Reference
Section titled “4. Command Reference”4.1. Media Playback related commands
Section titled “4.1. Media Playback related commands”Provides Player related actions. Use playcontrol.htm to get human readable response.
| TCP/IP and UDP | description | version |
|---|---|---|
player.htm?state=play |
Sets the playback state, which starts the playback at the currently selected playlist item. | 1.0 |
player.htm?state=pause |
Pauses the current playback. | 1.0 |
player.htm?state=stop |
Stops the current playback, the seeker is set to the beginning of the currently selected playlist item. | 1.0 |
player.htm?select=next |
Selects the next item of the playlist. If playback state is set, the playback of the selected item starts. | 1.0 |
player.htm?select=prev |
Selects the previous item of the playlist. If playback state is set, the playback of the selected item starts. | 1.0 |
player.htm?select=1 |
Selects the first item of the playlist. If playback state is set, the playback of the selected item starts. | 1.0 |
player.htm?select=99999 |
Selects the last item of the playlist. If playback state is set, the playback of the selected item starts. | 1.0 |
player.htm?mute=1 |
Mutes the player audio output temporary. | 1.2 |
player.htm?mute=0 |
Re-Enables the player’s audio output. | 1.2 |
player.htm?audio=0..100 |
Sets the global audio level to [0..100]%. |
1.2 |
player.htm?autoplay=1 |
Sets the autoplay state active. | 1.2 |
player.htm?autoplay=0 |
Sets the autoplay state inactive. | 1.2 |
player.htm?load=[fullpath] |
Loads a playlist XML file from disk, specified by [fullpath]. E.g.: player.htm?load=D:\My_Playlists\list1.xml.Note: use alphanumeric characters only (avoid characters like #, &) in filenames. |
1.2 |
player.htm?save=[fullpath] |
Saves the current playlist to a file specified by [fullpath]. E.g.: player.htm?save=D:\My_Playlists\list1_backup.xmlNote: use alphanumeric characters only (avoid characters like #, &) in filenames. |
1.2 |
player.htm?add=[fullpath, pause, stop, jump]&pos=[p] |
Adds a file or playlist item. If the additional parameter pos=[p] is used, the new item will be inserted at list position [p]. E.g.: player.htm?add=D:\My_Content\Image.jpg adds Image.jpg to the playlist. The file must located inside the default content directory. player.htm?add=pause adds a pause control item to the playlist. player.htm?add=stop adds a stop control item to the playlist. player.htm?add=jump adds a jump to first item control item to the playlist.Note: use alphanumeric characters only (avoid characters like #, &) in filenames. |
1.2 |
player.htm?move=[up, down, top, end, [t]]&select=[p] |
Moves the playlist entry [p] to the specified position. [t] can be used to define a desired absolute position. E.g.: player.htm?move=up&select=5 moves playlist item no. 5 one position up. E.g.: player.htm?move=2&select=7 moves playlist item no 7 to the position 2. |
1.2 |
player.htm?activate=[p] |
Activates the playlist item [p] |
1.2 |
player.htm?deactivate=[p] |
Deactivates the playlist item [p] |
1.2 |
player.htm?loop=[p] |
Activates the loop behaviour of item [p], if available |
1.7 |
player.htm?noloop=[p] |
Dectivates the loop behaviour of item [p], if available |
1.7 |
player.htm?delete=[[p], all] |
Deletes entry [p] from the playlist, [all] to clear the whole playlist. |
1.2 |
player.htm?refresh=[[p], all] |
Refreshes the meta-data (size, date, etc.) of the item [p] in the playlist. E.g.: player.htm?refresh=2 refreshes the meta data of item 2 in the playlist. |
1.2 |
player.htm?tmPerImg=[s]&select=[p] |
In case of an image sequence item this command changes the display time of each image; [s] seconds as float value, [p] position of the item to change; e.g. player.htm?tmPerImg=4.5&select=3 sets the time per image for this sequence at position 3 to 4.5 seconds |
1.2 |
player.htm?status |
Retrieves a comma separated list with status information
|
1.7 |
player.htm?status=index |
Retrieves the index of currently selected/ played item in playlist
|
1.7 |
player.htm?status=count |
Retrieves the number of items in the playlist | 1.7 |
player.htm?status=state |
Retrieves the state of the current selected/played item
|
1.7 |
player.htm?list=state |
Retrieves an overview of useful information as comma separated list. Format: a,b,c,d,e,f,g
|
1.7 |
player.htm?list=volume |
Retrieves the current audio volume setting.
|
1.7 |
player.htm?list=balance |
Retrieves the current audio balance setting.
|
1.7 |
player.htm?list=playing |
Retrieves informations about the play state of the playlist.
|
1.7 |
player.htm?list=showmode |
Retrieves the current showmode state
|
1.7 |
player.htm?list=playItem |
Retrieves the current selected playlist item position | 1.7 |
player.htm?list=position |
Retrieves the current stream position in percent
|
1.7 |
player.htm?list=seeker |
Retrieves the current stream position in more detailed mode. Format:
|
1.7 |
player.htm?list |
Retrieves a list of all items in playlist. One item per line. Per line contained information:
|
1.7 |
player.htm?item=mediainfo&select=[p] player.htm?item=mediainfo |
Retrieves media informations about the current selecteded playlist item if no select parameter is specified, or about playlist item
|
1.8 |
player.htm?seekerto=[f] |
Sets the stream position of an active playing stream based playlist item to a specific position. The presenter pipeline must be in showmode on state and the current played playlist item must be in play or pause state. [f] can be an integer [0 .. 100] defining the relative stream position in percent, or a double [0.0 .. 1.0] defining the relative stream position more precisely. |
1.7 |
player.htm?seekerby=[f] |
Used to change the stream position of an active playing stream based playlist item by a specified portion. The presenter pipeline must be in showmode on state and the current played playlist item must be in play or pause state. [f] can be an positive or negativ integer, defining the portion in milliseconds the stream position should be changed, or a double [-1.0 ..1.0] defining the portion in relative way. Examples: player.htm?seekerby=-10000 => goes 10 seconds backward from current stream position player.htm?seekerby=0.1 => goes 10% forward from current stream position |
1.7 |
player.htm?smoothborder=[1,0] |
Toggles the smooth border presenter feature | 1.7 |
player.htm?fullscreen=[1,0] |
Toggles the fullscreen presenter pipeline feature. | 1.7 |
player.htm?blank=[1,0] |
Toggles the blank screen(s) presenter pipeline feature. | 1.8 |
4.2. Receiving meta information about files
Section titled “4.2. Receiving meta information about files”Interface to receive informations about available media files
| TCP/IP and UDP | description | version |
|---|---|---|
mediafile.htm?list mediafile.htm?list&fmt |
Retrieves a list of all available media files onto the server (comma separated list). fmt: The response is given as HTTP side (one file per line). |
1.7 |
playlistfile.htm?list playlistfile.htm?list&fmt |
Retrieves a list of all available playlist files onto the server (comma separated list). fmt: The response is given as HTTP side (one file per line) |
1.8 |
calibfile.htm?list calibfile.htm?list&fmt |
Retrieves a list of all available calibration files onto the server (comma separated list). fmt: The response is given as HTTP side (one file per line). |
1.8 |
4.3. Receiving previews
Section titled “4.3. Receiving previews”Interface to receive preview images of playlist items
| TCP/IP and UDP | description | version |
|---|---|---|
preview.htm?select=[p] |
Retrieves the preview image of playlist entry [p] . e.g.: preview.htm?select=5 retrieves the preview image of playlist entry 5. |
1.7 |
4.4. Controlling render output behaviour
Section titled “4.4. Controlling render output behaviour”Get/set presenter pipeline specific parameters
| TCP/IP and UDP | description | version |
|---|---|---|
presenter.htm?get=globalcolor presenter.htm?get=globalcolor& fmt |
Retrieves the current global color settings (comma separated list).
|
1.7 |
presenter.htm?get=fullscreen presenter.htm?get=fullscreen&fmt |
Retrieves the current fullscreen presenter feature setting state.
|
1.7 |
presenter.htm?get=smoothborder presenter.htm?get=smoothborder&fmt |
Retrieves the current smooth border presenter feature setting state.
|
1.7 |
presenter.htm?get=blank presenter.htm?get=blank&fmt |
Retrieves the current blank screen(s) presenter feature setting state.
|
1.8 |
presenter.htm?globalcolor=[r,g,b] presenter.htm?globalcolor=[r,g,b]&fmt |
Sets new global color values. The presenter pipeline has to be in showmode on state. fmt: The response is given as HTTP side. r,g,b in the range of 0 .. 1000, empty color place for unchanged |
1.7 |
presenter.htm?smoothborder=[1,0] presenter.htm?smoothborder=[1,0]&fmt |
Enables, disables the smooth border presenter pipeline feature. fmt: The response is given as HTTP side. |
1.7 |
presenter.htm?fullscreen=[1,0] presenter.htm?fullscreen=[1,0]&fmt |
Enables, disables the fullscreen presenter pipeline feature. fmt: The response is given as HTTP side. |
1.7 |
presenter.htm?blank=[1,0] presenter.htm?blank=[1,0]&fmt |
Enables, disables the blank screen(s) presenter pipeline feature. fmt: The response is given as HTTP side. |
1.8 |
4.5. General program control
Section titled “4.5. General program control”| TCP/IP and UDP | description | version |
|---|---|---|
control.htm?present=1 |
Enables show mode while Output is displayed. | 1.0 |
control.htm?present=0 |
Disable show mode while Output is displayed. | 1.0 |
control.htm?shutdown=1 |
Shuts down the operating system. | 1.0 |
control.htm?shutdown=2 |
Shuts down the operating system and reboots. | 1.0 |
control.htm?exit |
Close the currently addressed running instance of the application. | 1.0 |
control.htm?calibrate=M0 |
Starts a camera-based recalibration on a single client system without any user interaction (1-click recalibration). | 1.0 |
control.htm?calibrate=MC |
Stops a running calibration without changing the currently used calibration ona single client systen | 1.0 |
control.htm?calibrate=N0 |
Starts a camera based multiclient recalibration without any user interaction (1-click recalibration) | 1.0 |
control.htm?calibrate=NC |
Stops a running multiclient calibration without changing the currently used calibration. | 1.0 |
control.htm?calibrate=status |
Returns 1, in case a calibration is running, 0 otherwise | 1.8 |
control.htm?execute=[filename][Param] control.htm?execute=”filename”]Param] |
Executes the specified file. The executable has to be located inside the subdirectory \Execute inside the data exchange directory of the server. Param: optional command line parameter Note: use alphanumeric characters only (avoid characters like #, &) in filenames. |
1.0 |
control.htm?preset=[x] |
Loads the calibration file “Preset[x].sps” that must located inside the default calibration folder. [x] defines an integer. example: control.htm?preset=12 loads the file “Preset12.sps” |
1.0 |
control.htm?settings=[x] |
Loads the calibration file “Settings[x].sps” that must located inside the default calibration folder. [x] defines an integer. The difference towards preset (see above) is, that the calibration file will be loaded by the GUI and not intern. example: control.htm?settings=1 loads the file “Settings1.sps” |
1.0 |
control.htm?clear=[xxx] |
Clears configurations and data.
example: |
1.7 |
control.htm?save=[filename] control.htm?save=[filename]&wait=[x] |
Saves the current calibration state to specified “filename”
|
2.0 |
control.htm?ShowOutput=0 |
Makes all current output windows invisible (on master) | 2.3 |
control.htm?ShowOutput=1 |
Makes all current invisible output windows visible again (on master) | 2.3 |
4.6. 3D model specific commands
Section titled “4.6. 3D model specific commands”3D-model depended computation control
| TCP/IP and UDP | description | version |
|---|---|---|
model3d.htm?status model3d.htm?status&fmt |
Retrieves the current status of the 3D-model engine, as text string.
|
1.6 |
model3d.htm?process |
Starts the 3D-model computation, based on current settings. Available response strings:
|
1.6 |
4.7. Script Engine commands
Section titled “4.7. Script Engine commands”Interface to control the script engine
| TCP/IP and UDP | description | version |
|---|---|---|
script.htm?status script.htm?status&fmt | Retrieves the current status of the script engine, as text string.
| 1.6 |
script.htm?execute=filename script.htm?execute=filename&pa ram=[...] | Executes the specified script file. Available response strings (defined in c conform string format definition):
In additional to the script file name to execute, a parameter string can be defined to define variables. A variable can defined by:
No format specificaton implies a string value. More than one variable can defined by a semicolon separated list. Example: The script | 1.6 |
script.htm?abort | Aborts the execution of a currently processed script. | 1.6 |
info.htm?displays info.htm?displays&fmt | Retrieves a list of all available displays fmt: The response is given as HTTP page. Text based version defines one display per line as comma separated parameter list: adapter id, name, type of display, width, height, pos-X, pos-Y, id-string | 1.7 |
4.8. Common Information commands
Section titled “4.8. Common Information commands”Interface to retrieve various meta- and system information.
| TCP/IP and UDP | description | version |
|---|---|---|
info.htm?displays info.htm?displays&fmt |
Retrieves a list of all available displays fmt: The response is given as HTML page.Text based version defines one display per line as comma separated parameter list: adapter id, name, type of display, width, height, pos-X, pos-Y, id-string, Handle |
1.7 |
info.htm?desktopdisplays info.htm?desktopdisplays&fmt |
Retrieves a list of all available desktop displays fmt: The response is given as HTML page.Text based version defines one display per line as comma separated parameter list: adapter id, name, type of display, width, height, pos-X, pos-Y, split-Rows, split-Cols, id-string, Handle |
2.5 |
info.htm?deskpartident&possz= [p]&id=[i]&name=[n]&fmt |
Shows an identification window on the specified place
|
2.4 |
4.9. Project Manager commands
Section titled “4.9. Project Manager commands”Interface to control the project manager.
| TCP/IP and UDP | description | version |
|---|---|---|
pm.htm?status[&fmt] |
Retrieves the current status of the project manager.
Other lines: a,”b”,”c”: This lines contain informations about available project steps.
|
6.0.2 |
pm.htm?load=project[&fmt] |
Tries to load the specified project. A
|
6.0.2 |
pm.htm?start=step[&queue][&fmt] |
Tries to start the specified project step
|
6.0.2 |