Skip to content

Watchout v.6

The freemode is prepared as usual, a possible split has to be set up, the projector outputs used have to be selected, a camera has to be selected, the mode of operation has to be selected and further parameters can be adjusted.

Learn more about the configuration of VIOSO in free mode: free-mode

As soon as the calibration is started, the calibration process is identical to the project mode, which is elaborated below.

In order to be able to use the result of a calibration in Watchout, it is necessary to set the export accordingly.

If you choose the Watchout Preset, the most things are preset accordingly to the needs of watchout.

The following is important for the export:

  • Watchout 6 is only able to use MPCDI V1 files.
  • You need to export a virtual content rectangle. Thats the complete screen as result of the calibration. Otherwise Watchout will create an infinite sized screen that will crash the Software.
  • Another big role is played by the number of columns and rows used to create the MPCDI file.
    Simple screens can be created with a quarter of the resolution; if the surface becomes more complex, the values have to be corrected upwards.
    The resolution represents the maximum value, more rows and columns are technically not better, or a value that is too high can impair the performance of the media server.
  • Another challenge is the MPCDI format in the edges. Since the measurement results tend to fray at the edges, it helps to make the warp a little larger and to mask the edges. The masks are then also exported and displayed correctly.

Once the MPCDI file is created, it can be imported into Watchout. A corresponding screen is created in Watchout and the warps, blends and masks for the screen are saved.

The export parameters can be adjusted in the Designer by selecting the export node:

Click on the node to activate the inspector providing the export parameters:

  1. Export Definition
    The preset for watchout is fixed, no changes can be made here.
  2. Virtual Content Mapping Parameter
    Virtual content rectangle - is the outline of your calibrationresult. If cheched it’s exported as required in Watchout.
    Width and Height - Here you can enter the resolution of the content you are expecting. If you leave 0 - 0 the calibrated pixelspace will be used.
  3. Special Mapping Parameter
    Checkbox - exports in case the used 3D model
  4. Export Destination
    Path - Enter an individual export path
    File Name Definition - Enter an individual file name
    Transfer all - Transfers all files to export destination
    create Backup - creates a Backup of the export in the VIOSO folder
  5. Transfer to remote machine
    Ability to transfer the calibration automatically to clients if needed
  6. Display Split Parameter
    Keep Splits - should be unchecked if you use a Mosaik setup
  7. Grid Parameter
    Rows and Columns - The Mesh thats used to create the MPCDI file
  8. Exclude Parameter
    check to exclude parameters from export
  9. Note
    Link to the Helpdeskpage

Calibration (same for free mode and projectmode)

Section titled “Calibration (same for free mode and projectmode)”

Calibrate the Screen as needed. Learn more here: Calibration

When exporting MPCDI files, the edges may be jagged. In order to master this phenomenon, you should always warp a little larger. A few pixels are enough. If you now set output masks at the edge, these are exported separately and then displayed correctly.

Learn more about masking here: Projector masking

Export the calibration as set in the designer (project mode) or configure manually (free mode). Imperative values for Watchout are:

  • MPCDIv1
  • check virtual “content rectangle”
  • change the amount of columns and rows to get a good result

Open your show or create a new show

Import a MPCDI File using the File menu:

Choose a File, a tier to import to and an offset. The offset is needed if you use more than one screen in your project.

Only MPCDI files of version 1 are accepted

The Stage shows the imported Screen. The blends and masks are imported to the media area

Enter the IP adress and outputchannel and the correct resolution of the Output. If you want to use more than one screen, enter the stage position to your needs, to prevent an overlap of different screens.

Now the screen is prepared and ready for content placement.